Add flour used cartridge details
HP C3900A Toner Cartridge (HP 4V/4MV/4VC)
Canon EP-B cartridge (CANON LBP-BX)
A separate cartridge ª±
Remove the cartridge to open the machine on the table, first of all take off on a spring drum, living with a side oblique mouth clamp metal pin, pull out force, both sides of the silver metal pin can be pulled out after the cartridge divided into two parts, one is with Gu Xin Fei Fen collection pieces are available with a magnetic roller side bunker. ª¥
2 ª± replacement Gu Xin and scraper, clean Feifen
Will Feifen collect pieces of gray plastic drum on both sides of the white clamp on the screws out, pull out the white plastic clamp, Gu Xin can be taken out. Then taken out of discharge roll, twist off the two screws out scraper scraper to clean Feifen all, then scraper, discharge rollers, photosensitive drum according to the state before the restoration of a good split (Note Gu Xin and both ends of the white plastic clamp and the direction of discharge can not be anti-roll). The number of laps gently rotate Gu Xin, drum surface should be clean. If the drum surface with residual powder, should be replaced scraper. ª¥
3 ª± filling toner
If your cartridge is not original toner cartridge filling over the first irrigation powder, filling powders do not need to clean up the bunker and the magnetic roller, or need to roll on the bunker and the magnetic toner to clean up. Remove the plastic cover on the bunker, the Amano 4V/4VC toner Shake slowly poured into the bunker again, cover and plastic cover, gently roll the number of rotating magnetic ring, magnetic roller ink should be a uniform adsorption powder. ª¥
4 ª± cartridge assembly
Will be available for collection of pieces by bunker and Feifen open position when the installation of recovery, plugged in on both sides of a small metal card sales Shanghao spring. Toner bottles, should open the drum shutter, gear up the side of light switch Guxin few laps, drumhead remove residual toner Jibei, installed ready for use. ª¥
Please keep the top: ª¥
(1) When the paper was noticed black spots, that drum has been damaged should be replaced. ª¥
(2) the increase should be of high quality laser toner machine toner, or print quality is not guaranteed.
-------------------------------------------------- ------------------------------
HP C3903F Toner Cartridge (5P/5MP/6P/6MP)
HP 92274A Toner Cartridge (HP 4L/4ML/4LC/4P) powder filling and cleaning methods:
First, the 92274A cartridge flat on the table, first put off the bezel (block single drum and can turn the side of a spring), in the shell side baffle spring that there is a deep hole, there is a small screws to take out the small screws (3903F toner cartridges without this small screws). ª¥
Second, the cartridge upside down (read, 92274A or C3903F of that side down), saw four clamp, and then further on the right to see (that is, Gu Xin end of the line with gear) are a pair of clamp, one on each sides of clamp to the clamp slowly torn off and the cartridge was divided into two parts, namely, powder for part (a bunker and the discharge roller) and with a single drum part.
Third, replacement of a single drum (not-for-Gu Xin can save this): the single drum clamp at both ends of pins or remove the old one out put the new single-drum drum, then pin or clamp Shang Hao, gently rotate Gu Xin, Gu Xin surface should be clean, if the toner can not be scraped scraper should be replaced.
4, first bunker that part of the discharge roller and a small gear removed, the residual powder and Feifen clean, bottles and toner, then discharge roller and pinion back the original position.
5, according to demolition and waste bunker bunker when the relative positions of the two parts together and clamp are all restored to its original state (or cartridge will leak powder), having a good small screws and bezel, update the cartridge completed. ª¥
Note:
1, the demolition of the time to be careful not to clamp broken.
2, the increase should be pure laser toner toner, or toner cartridges will reduce the use of time and pollution of the machine.
-------------------------------------------------- ------------------------------
HP C3906F (5L/6L/6L Pro/6L Gorl) 3100
The following is 5L, 6L toner powder filling and cleaning.
First, remove the cartridge to open the machine, oblique mouth with a metal clamp to live one side of the pin, pull out force, both sides of the silver metal pin can be pulled out after the cartridge is divided into two parts, one is Feifen with Gu Xin collection of pieces, with a magnetic roller is one piece for the powder. ª¥
Second, clean up Feifen: The Feifen collect pieces of the light blue drum set aside on both sides of the metal pin, remove the photosensitive drum in the dark stable office, discharge roll out, then nail scraper spin on the two Luo Next, remove the scraper, slowly pour the waste bunker in Feifen, then scraper discharge roller, photosensitive drum according to the original location of recovery (For replacement Gu Xin, this time the old Gu Xin scraper, scrape board can be replaced by new). ª¥
3, filling toner: the piece on the magnetic roller for powder-free rotary screw gear side of the Luo, the win could see a purple plastic case after the plastic cover, open the lid, the bunker on the inside and the magnetic roller All toner to clean (if you do not clean up magnetic roller and the bunker print proofs may be made shallow bottom ash or writing), the magnetic roller bottles and, application of force at this time hold down the magnetic roller, magnetic roller to prevent from in situ. Laser printer toner to shake slowly for the bunker into, cover and plastic covers, having a good plastic case (and you should pay attention to: the end of the axial magnetic roller and the plastic case on the semi-circular semi-circular holes to good), gently rotating magnetic roller gear side of the number of laps, so that toner on the uniform. ª¥
4, will be available for collection of powder parts and Feifen apart piece by installation of recovery time position, plugged in on both sides of metal card sales. Toner bottles, should open the drum shutter, gear up the side of light switch Guxin few laps, drumhead remove residual toner Jibei, installed ready for use.
Please keep the top: ª¥
(1) When the paper was noticed black spots, that drum has been damaged should be replaced. ª¥
(2) the increase should be pure laser toner toner, or toner cartridges will reduce the use of time and pollution of the machine.
-------------------------------------------------- ------------------------------
HP 29X (HP C4129X) laser toner cartridge filling method
1, separation cartridge
Open the laser remove the cartridge on a stable table, will Guxin ends four screws (two per side) to remove, the two clamp fixed Guxin pull out, open the tailgate to drum Gu Xin core out, and then roll out the discharge from the cartridge inside the bunker and Feifen connect the two metal pins out off by disclosing, this time with the waste bunker bunker was divided into two parts, namely, powder for some ( with a magnetic roller) and Feifen collection component.
Second, the replacement Gu Xin and scraper, clean Feifen
Scraper on the waste bunker down the two screws tighten, remove the scraper, the Feifen all clean, then scraper discharge roller, photosensitive drum according to the state before the restoration of a good split (Note Guxin direction). Number of laps gently rotate Gu Xin (To replace Gu Xin and scraper to complete this step)
3, filling toner
The magnetic roller bunker gear this side of the side without the two screws on the screw, the outward pull the screws to take off the shell (magnetic roller of the end into one), then only one end of the fixed magnetic roller, the Magnetic Roller withdrawal, then find a bunker on the strip gap, the toner bottle of 5000 after shaking along the slot into the bunker, the toner After filling in turn the magnetic roller, remove the shell, and corresponding to the position before the screws by demolition installed (installed with a magnetic roller should pay attention to this side of the gear you want to install in place), the number of laps gently rotating magnetic roller, magnetic roller should be a uniform adsorption toner.
4, assembly cartridge
The two parts together, the two pins inserted to be in place, then update the cartridge should be completed.
Note:
The bunker must be filled (including the magnetic roller) and the waste bunker where the toner to clean up.
-------------------------------------------------- -----------------------------
92274A Toner Cartridge (HP 4L/4P/4ML/4MP/4PJ/4LC) powder filling and cleaning methods:
First, the 74A cartridge on the table, first put off the bezel (single drum and can block the rotation, the side of a spring), in the shell side baffle spring that there is a hole, there is a small screw to take out the small screws.
ª¥
Second, turn the cartridge over (written down the side 74A of that), and saw the four clamp, then further on the right to see (that is, Gu Xin end of the line with gear) are a pair of clamp, a clamp on both sides of each face, these clamp slowly disengaged, toner cartridges were divided into two parts, namely, powder for part (a bunker and the discharge roller) and with a single drum part.
Third, replacement of a single drum (not-for-Gu Xin can save this): the single drum clamp at both ends of pins or remove the old one out put the new single-drum drum, then pin or clamp Shang Hao, gently rotate Gu Xin, Gu Xin surface should be clean, if the toner can not be scraped scraper should be replaced.
4, first bunker that part of the discharge roller and a small gear removed, the residual powder and Feifen clean, bottles and toner, then discharge back into the original roll and small gear position.
5, according to demolition waste bunker when the bunker and the relative positions of the two parts together and clamp are all restored to its original state (or cartridge will leak powder), having a good small screws and bezel, update the cartridge completed.
6, note:
1 ª± at the time of demolition should be careful not to clamp broken.
Plus 2 ª± the toner laser toner should be pure, otherwise it will shorten the cartridge to use time and pollution machines
-------------------------------------------------- ------------------------------
HP 92295A Toner Cartridge Canon EP-S EP-T
The first step:
Remove the toner cartridge from the machine, flat on a clean table, clean the surface dust, then both sides (two per side) a total of four plastic locator card pin disconnect, and then clipped the top two positive expansion card, make compact components and cover (cover) plate separation. ª¥
Step Two:
Will
Components on the right side of a white plastic wire electrode expansion card unplug (or hold down the inward side of electrode wire, and then move up), remove the wire electrode, the electrode wire carefully cleaned, this time for the component can be powder parts and recycling (Feifen) pieces separated. ª¥
Third step:
The recovered pieces (Feifen collecting cases) on both sides of the green photosensitive drum gong screw unscrewed, remove the pin on both sides, remove the photosensitive drum (photosensitive drum, such as serious wear and tear, you should replace the OPC drum new purchase) and then the photosensitive drum waste bunker below the top of both sides of the two scraper gong screw unscrewed, remove scratch pull, slowly pour Feifen Feifen collection warehouse. ª¥
Step Four:
Will be available for pink pieces of white plastic cover to open the right to buy the toner in the bottle hard to shake, open the bottle will slowly into the bunker toner, cover and wipe, and then press the process will Toner box reduction. (Note: when installing OPC photosensitive drum bevel helical parts and recycling is on the right). ª¥
Step Five:
Toner box is completed, will it upside down, open the cartridge shutter photosensitive drums, a few light Rotary ring gear side, then instantly clean the toner cartridge inside the drums, and then Tiger will be a small skin toner boxes and other parts of the slit in the dust blowing off, installed to use. ª¥
Note: ª¥
1, update the toner to the photosensitive drum surface smooth, not a scratch, or scratch marks will be updated in the printed materials of reaction (not damage the printer). ª¥
2, do not join the other uses toner, copier toner by is to avoid damaging the photosensitive drum, laser printer drum for coating thin and uneven toner particles easy to wear. ª¥
3, the action should be stable during the operation, carefully, not too much force, or mechanical damage. ª¥
4 bottles and test machines, such as printed materials appearing on signs of leakage of powder can be to print a few, traces of powder can leak to lift.
-------------------------------------------------- ------------------------------
Laser Toner Cartridge Canon LBP-JX plus powder method introduced
How to properly replace the Canon JX ª¤ laser printer cartridges in the photosensitive drums and toner.
Canon LBP-JX laser printer is a Canon introduced the last two years the price of relatively inexpensive laser printer 600DPI A3 format, although the low price of the machine, but the high price of EP-J cartridge, OPC then prone to breakdown point Therefore, many users are eager to replace the EP-J control photosensitive drum in the toner drum and processing methods. After we explored a long time, summed up a set of practical and reliable way to replace. Here we are willing to specific methods described below to reduce the user's printing costs.
1, separation cartridge: the use of less sharp partial nose pliers to the left and right side of the metal cartridge pin pulled out, then flip cartridge the cartridge back and two white plastic base of the two small springs, after rotating 90 degrees out, At this time the cartridge is divided into two parts.
2 ª± Remove the old OPC ª¥ this part of the OPC drum will be flat on the operating table, so look carefully, you will find there end of the fixed OPC metal caps have a white plastic small round flat circle. Cross point screwdriver flat head with a live cartridge of this metal head with a hammer gently tapping the other end of the screwdriver, then Guxin a thin metal stick the other side was knocked out, gently pull outward, running through OPC length of metal rod can be taken out and put forward the old OPC.
ª¤
3 ª± clean Feifen: Remove the OPC, the scraper is exposed, the two screws on the scraper spin out, remove the scraper, the Feifen poured out, then well scraper.
ª¤
4 ª± install a new OPC: JXOPC generally without gear, the gear needed to remove the old OPC OPC installed in the new, the installed gear after gear one should pay attention to OPC is the other end is a straight bevel gear, to the cartridge when installed must pay attention to the direction it should not installed backwards. Photosensitive drum put away after the installation of metal rod with a notch when the first insert in one end, then gently push inwards, and finally re-use hammer about to return to its original position, held in place by a small circle of white plastic.
ª¤
5 ª± filling toner: If your cartridge is not too bad irrigation do not need to clean up the toner residual powder in the bunker. Lifted first magnetic roller scraper on the next two screws to take out the scraper, then there is a gap next to magnetic roller, the toner poured from the gap of the bunker, the toner after filling the scraper Shang Hao Good gently rotating magnetic roller, magnetic roller absorbing powder should be uniform.
6 ª± assembled cartridges: two parts of the drum together, having a good side of the metal pin and two small springs, cartridge update is completed.
-------------------------------------------------- ------------------------------
Canon LBP-KT laser printer toner powder method of introducing additional
1, separation cartridge: Remove the cartridge on the table to open the machine, the first two springs on the cartridge off, living with a side oblique mouth clamp metal pin, pull out force, both sides of silver metal pin pulled out after the cartridge is divided into two parts, one is Feifen with Guxin collection pieces, with a magnetic roller is one piece for the powder.
Second, the replacement Gu Xin and scraper, clean Feifen: The Feifen collect pieces of gray on both sides of the imaging drum on a white plastic clamp screws (two per side) screw out, pull out the white plastic pin, Gu Xin can be taken out. Then taken out of discharge roll, twist off the two screws out scraper scraper, to clean up Feifen all, then scraper discharge roller, photosensitive drum according to the state before the restoration of a good split (Note Gu Xin and both ends of the white plastic pin in the direction can not be anti-). The number of laps gently rotate Gu Xin, drum surface should be clean. If the drum surface has residual powder, should be replaced scraper.
3, filling toner: the pieces of bunker and magnetic powder for the ink roller clean. Remove the plastic cover on the bunker, the KT toner Shake slowly poured into the bunker again, cover and plastic cover, gently roll the number of rotating magnetic ring, magnetic roller should be a uniform adsorption toner.
4, assembled cartridge: for powder parts and Feifen will collect pieces installed by open position when the recovery card plugged in on both sides of metal sales. Toner bottles, should open the drum shutter, gear up the side of light switch Guxin few laps, drumhead remove residual toner Jibei last bottles and two small springs on the machine to use.
Please keep the top: ª¥
(1) When the paper was noticed black spots, that drum has been damaged should be replaced. ª¥
(2) the increase should be pure laser toner toner, or print quality is not guaranteed.
