HP printer cartridges plus ink commonly used method

HP_27_28_56_57_58_59_816_817 filling method

No. 27 Black Ink Cartridge (HP C8727A)
28 color ink cartridges (HP C8728A)
No. 56 Black Ink Cartridge (HP C6656A)
57 color ink cartridges (HP C6657A)
58 Photo Cartridge (HP C6658A)
59 Photo Cartridge (HP C6659A)
No. 816 Black Ink Cartridge (HP C8816A)
817 color ink cartridges (HP C8817A)

Cartridge only last a letter marking a different capacity
Black cartridge filling Method: (27,56,816)
1, the cartridge top label torn off, see the label the following five holes;
2, one of the needle into the hole for refilling, and fill the ink;
3, wipe around the hole, labeled.

Color cartridge filling method: (28,57,817)
1, the cartridge top label torn off, see the label the following five holes;
2, distinguish colors, have a hole for the red, blue two hole, two holes for the yellow;
3, spray pad Zhang good points below, can not afford to waste paper in the tissues, this is to prevent the ink from the nozzle cross color,
If the string is slightly colored, multi-hit a few blocks of color can be resolved (for the nozzle part of the series of color can follow this method).
4, the needle into the hole for refilling, and fill the ink
5, wipe around the hole, labeled.

Note:
28,57,817 three kinds of color ink cartridges contained in the primary colors: blue (sky blue), goods (purple), yellow (bright yellow);
58 photo cartridge contained in the primary colors are: light blue, light goods, black;
59 photo ink cartridge contains black colors are: light gray, dark gray and black.
58,59 No. cartridge filling method with 28,57,817, pay attention to distinguish colors, preferably with a clean toothpick inserted into the space within the exploration of its color.
Refilling ink cartridges should not be too much ink will inject more overweight, causing the printer does not recognize cartridge can not print.
Color ink cartridge refilling should strictly control the amount of cartridges shall be marked on the total amount of ink.
If the injection of ink will spill over, causing the ink filling holes from the upper string of color, so it is not good solution

Color cartridge model: hp 51625A/51649A/51649G/51640/61641A/51644 /
C1823A/C6578A/C6578D/C1823G/C1823D

1. In accordance with the instructions out the printer cartridge, sealed with tape the bottom of the nozzle
2. With a flat head screwdriver along the edge of the four corners of the ink cartridge cover gently prized open the lid, corresponding to the color of any one cell from each hole slowly filling the ink (mixed with ink to prevent injection, using a toothpick to test in advance sponge within each ink color) about 7-8 percent full attention sponge, sponge capacity of not more than is appropriate, the proposed 5ml
3. The lid, sealed with tape
4. Opened the nozzle end of the strip, observe whether the phenomenon of infiltration ink, with no tissue paper or wet paper towel dipped in ink leakage test, static discharge after 30 minutes, can be installed

Note: If the poor ink seepage may plug or nozzle has been placed on too long and dry, it is recommended to use 80 degrees of pure hot water soak for 10 minutes (do not get wet or come across the circuit board), with no tissue or try a clean wet paper towel dipped the nozzle end, installed after 30 minutes of static discharge into the print job.

Black Ink Cartridge Model: hp 51626A/51626G/C1843A/C6577A/51629A /
51629G/51640A/C6614D/C6615A/51623M

1. First of all, find a clean glass and a syringe, also prepare some free tissue paper or wet paper towels and tape
2. In the top left of ink through a hole (for refilling), but be careful not to puncture hole when the cartridge inside the balloon
3. With tape to the top of the inflatable cartridge and the bottom of the vent holes with tape to seal their
4. Refilling slowly from the worn to the ink refilling hole into a room full of 7-8 can, in the refilling process should not insert the needle too deep, so as not to burst the balloon with no tissue paper or wet paper towels to clean the ink hole , and then tape to seal the refilling hole
5. The cartridge inverted static discharge 1-3 minutes, then opened a vent tape the prepared syringe aligned its vents, Daochou air to the Syringe 4ml, remove the syringe, and immediately seal the pores. Note: If too much air Choude not cause negative pressure caused by ink
6. The ink is coming to observe whether the ink drop out of the nozzle end, if it shows there is no transfer balance pressure, repeat the above operation procedure until the ink is not dripping from the nozzle is appropriate, and then installed to print the work

Note: The above procedures are prepared in your glass order to prevent the ink stain on your clothes

Color cartridge model: hp 51641/1823/6578/6625

1. In accordance with the instructions out the printer cartridge, sealed tight with tape heads
2. With a sharp tool to plug the cartridge filling hole at the top of a small plastic plug or beads pressed into the cartridge in
3. The needle into ink, the corresponding color ink injected slowly (to prevent ink mixed note, with a toothpick test in advance the color) until the sponge is full of ink
4. Stand for a few minutes, seal the refilling hole
5. Remove the nozzle on the tape, installation, testing, printing

Black Cartridge: 51645A/51645G

1. In accordance with the instructions out the printer cartridges
2. The cartridge inverted, that is, the nozzle facing up, then thrown off the nozzle refilling hole near the top of the sticker, exposing steel ball
3. With his putter to the ball forward within the cartridge, the ink needle into his position, slowly inject ink
4. Pulled out needle, sealed tight with a plug hole refilling
5. Refilling with syringes hole extraction from the gas cartridge (5ml suitable recommendations, greater than or less than 5ml pressure imbalance will lead to poor or out of ink)
6. Refilling with spare beads plug the hole or by other means refilling hole to be closed
7. The vertical cartridges over the nozzle down on absorbent tissues on the good, about two minutes, some of the ink suitable nozzle leakage. The normal ink and installation testing, printing.