The actual operation of laser printer irrigation powder
Laser printers in the business office system are very common, because of course the strong performance of laser printers and relatively inexpensive cost later. Even so, the user also hopes to further reduce the print on this basis the cost of filling powder was used. Irrigation supplies powder is not the original manufacturer's products, in many practical applications because of compatibility and design issues cause problems. So good to address these issues become issues of concern to users. This issue I will be filling powder laser printers the most common questions explain the failure to do analysis in the hope of solving the practical application of the user appear in the powder filling failure.
The price of irrigation
Said filling powder cheap, but has not introduced a common standard filling meal prices. Based on actual experience, filling powder laser printers usually between 40-60 dollars. Irrigation powder consists of two steps, first filling powder, and second, the counter will be cleared toner cartridges. Irrigation will be because the price of toner powder The quality and differentiated, the higher the price the better the quality toner.
The actual operation of the toner filling
Toner cartridges usually have two, one is with a toner cartridge chip toner counter, there is a counter that is not with a chip cartridges. Because of the profit the control of the toner and now the original basically adopted the counter chip design, so the author is here to explain the main counter chip with the powder method of irrigation.
The first is to complete filling toner cartridge dismantling:
Cartridge disassembled ready tools: Cross screwdriver, tweezers, bend awl, cotton, tip clamp, 50ml plastic syringe 1
Powder filling tool
1, first cartridge flat Guxin upwards, tweezers remove the cartridge positioning pins on both sides of a small metal bolt and pulled out both sides of the cartridge, you can open the cartridge.
2, replace the imaging drum, scraper. Photosensitive drum in the waste bunker at one end, fear of light and crash. Photosensitive drum side of the fixed pin pulled out, remove the screw the other end of the first pin and then pull out. This can easily remove the drum. The photosensitive drum charge roller PCR following carefully taken down. Point to note is not to force or solvent cleaning charge roller, so as not to damage the surface coating affect print quality. The following is a scraper charge roller, the fixed scraper to remove the two screws, remove the scraper, the waste bunker after the Feifen clean, then the order were then scraper, charge roller, photosensitive drum Replace. After installation, on both sides with both hands to promote the photosensitive drum gear, so that drum rotation, until the photosensitive drum surface, the residual powder was Guajing up.
3, filling powder. Open toner bottle plastic cap to retain sealing film, in a sealed chip has a small mouth, do not tear the sealing film, sealing film is not difficult to control the amount poured out of toner. Then unplug the syringe push column, the syringe tube inserted in the hole, and then slowly poured into the tube to the syringe toner, toner down if the toner bottle can not squeeze the toner bottle. Let the syringe into the tube of the toner to the toner own barn, while observing the syringe tube flow inside the toner, and gently brush against the syringe tube, when the toner is no longer flow to the toner warehouses, and remain in syringe within the syringe tube toner has been accounted for 80% of the time, pushed into the syringe column, gently push inwards, while observing the bubbles in the syringe into the ink toner warehouse situation, when the toner is no longer found in sports or where there is pressure to push, to pull out of some. Pushing and pulling it repeatedly, until the syringe into the tube all toner toner warehouse. Note pushed inwards when not push too fast, to avoid compaction toner, ink toner is compacted into the hamper. Once the toner compaction, first pull it out push column about reducing the pressure of the toner storage and the syringe (this step must not province), pull out the syringe, the syringe facing up, brush the light hit the syringe, let loose toner then insert the cartridge in the hole for pouring powder.
4, the opposite direction back onto cartridges and used cotton wool to wipe clean, Gu Xin, and charge roller.
5, the reset pin when the attention to a little bit aside to facilitate the next plus powder
Laser printers are basically the same way of filling powder. Although different brands of cartridges will vary, but generally the way in dismantling the case. Be noted that in this way can be an unlimited number of times is not the filling. Because the cartridge in the printer is a lifetime limit. Powder filling method with only about four or so filling, powder filling, after the document appears to print out writing short, bottom ash weight, indicating that Guxin life to. Can find the same type of alternative Gu Xin, according to the steps prior to said filling powder replaced Gu Xin. Install the new Gu Xin, you can continue printing.
