Toner powder method increases
HP C3900A Toner Cartridge (HP 4V/4MV/4VC)
CANON EP-B cartridge (CANON LBP-BX) filling powder and cleaning methods.
1, separation cartridge
Open the machine remove the cartridge on the table, first off cartridge on a spring clamp to live with Oblique side of a metal pin, and external force pulled out, both sides of the silver metal pin can be pulled out after the cartridge divided into two parts, with the OPC side is Feifen collection pieces, with a magnetic roller side is for the bunker.
Second, replacement of OPC and the scraper, clean Feifen
Feifen collect pieces of the drum on both sides of the gray white plastic screw on the clamp screw out, pull out the white plastic clamp, OPC can be taken out. Then discharge roller to take out, screw off the two screws out on the scraper scraper to clean up Feifen all, then scraper, discharge roller, photosensitive drum according to restore the state before the demolition of a good (note the OPC and the at both ends of the white plastic clamp and the direction of discharge can not be anti-roll). Gently rotating OPC for a few laps, drum surface should be clean. If the drum surface with residual powder and timely replacement of scraper. ке
3, filling toner
If your cartridge is not original toner cartridge before filling the first filling powder, filling powders do not need to clean up the bunker and magnetic roller, or roller must be on the bunker and magnetic toner to clean up. Remove the plastic cover on the bunker, the 4V/4VC toner shake a shake and then slowly poured into the bunker, the cover plastic cover, gently rotating magnetic roller for a few laps, magnetic roller should be able to uniform adsorption toner .
4, assembly cartridge
Will be available for collection of pieces of bunker and Feifen to install when you click open the recovery, plugged in on both sides of a small metal card sales Shanghao spring. Good cartridge installed, should open the drum baffle, OPC up the side of light switch gears for a few laps, drum heads remove residual toner Jibei installed capacity can be used. ке
Note that the top thing: ке
(1) When the paper appeared on a regular black spots, that drum has been damaged, should be promptly replaced. ке
(2) the increase should be of high quality toner laser toner, or print quality is not guaranteed.
HP C3903F Toner (5P/5MP/6P/6MP) HP 92274A Toner Cartridge (HP 4L/4ML/4LC/4P) filling powder and cleaning methods ---
First, the 92274A cartridge flat on the table, pluck the first baffle (blocking a single drum and can rotate its side of a spring), in the shell side baffle spring that there is a deep hole, there is a small screws, the screws taken out this little (3903F Toner do not have this small screws).
ке 2, the cartridge upside down (read, 92274A, or down the side of the C3903F), saw four clamps, and then further on the right to see (that is, OPC with gear Cabanatuan) There are a pair of clips, on both sides of each face a clamp to the clamp slowly torn off and the cartridge was divided into two parts, namely, for the powder part (with bunker and discharge rollers), and with a single drum part.
Third, replacement of a single drum (OPC can be omitted without changing this): the single-drum at both ends of pins or clamps removed, the old replacing the new one-out single-drum drum, then pin or clamp Shang Hao, gently rotating OPC, OPC surface shall be clean, if a toner can not be scraped off to be replaced scraper.
4, first bunker on the part of the discharge roller and a small gear removed, the residual powder and Feifen clean up the bottles and toner, then discharge roller and pinion back in their original position.
5, according to demolition and waste bunker bunker when the relative positions of the two parts together, so that all clamps are restored to their original state (otherwise the cartridge will leak powder), Shang Hao small screws and baffle, toner cartridges that is updated been completed. ке
Note:
1, in the demolition of the time to be careful not to clamp cutting the.
2, the increase should be pure laser toner toner, otherwise it will shorten the cartridge usage time, while pollution of the machine.
HP C3906F (5L/6L/6L Pro/6L Gorl) 3100 Toner powder filling and cleaning methods
1, open the machine remove the cartridge. I live in a clamp with inclined side of metal pins, and external force pulled out, both sides of the silver metal pin can be pulled out after the cartridge is divided into two parts, with the OPC Feifen side is the collection of pieces, with a magnetic roller side is for the pink parts.
ке 2, cleaning Feifen: The Feifen collection of pieces in light blue on both sides of a metal drum pin set aside, remove the photosensitive drum in the dark stable office work out discharge roller, scraper and then on the two bolt Under rotation, remove scraper Feifen gradually pour in the waste bunker, then scraper, discharge roller, photosensitive drum according to the original location of recovery (For replacement of OPC, scraper at the moment, the old OPC, scraper with a new one can be).
ке 3, toner filling: will be available for pink pieces of the magnetic roller gear side of the bolt without rotation, the win can be seen, after a purple plastic case plastic cover, open the cover, will be inside the bunker and magnetic roller All clean up of the toner (if you do not eliminate the magnetic roller, and printing proofs bunker or the handwriting may appear at the end of gray hair light), magnetic roller bottles and, this time hold down the magnetic roller application of force to prevent the magnetic roller from the in-situ. The laser printer toner for the shake and slowly poured into the bunker, the cover plastic cover, Shang Hao plastic case (At this point should be noted that axial magnetic roller on the end of the semicircle with the plastic case on the semi-circular hole pairs good), gently rotating magnetic roller on the side of gear for a few laps, so that toner on the uniform.
ке 4, will be available for collection of powder parts and pieces Feifen to install when you click open the recovery, plugged both sides of the metal card sales. Good cartridge installed, should open the drum baffle, OPC up the side of light switch gears for a few laps, drum heads remove residual toner Jibei installed capacity can be used.
Note that the top thing: ке
(1) When the paper appeared on a regular black spots, that drum has been damaged, should be promptly replaced. ке
(2) the added toner should be pure laser toner, otherwise it will shorten the cartridge usage time, while pollution of the machine.
