Toner Replacement Tutorial

Cartridge rated at around 6000-10000 life in general, after long-term use later, when you find the output image Talking about the manuscript, there is a serious black spot stripes, even if you are useless no matter how repair and maintenance when the cartridge's life can be considered truly to the end, when the need to be replaced. Difficult to replace the cartridge that is not difficult, but not to the effect that easily Department and this one is a bit of learning, the following in order to drum on the toner powder separate, for example, to make a brief introduction.
First of all, turn off the printer power supply remove the cartridge, and then use pliers grip the side of the metal pin, forced out carefully pulled out (or sold directly to the nail in, open the cartridge and then taken out), under normal circumstances, when we are cartridge can be found can be divided into two parts, with a magnetic roller is for the pink part, while light-sensitive selenium is Feifen the collection component.

First look for the pink part, first magnetic roller gearless side of the screw rotation, opened the plastic cover, and then toner warehouses and magnetic roller on the toner with a soft brush and so on all the clean up. Then magnetic roller then re-install is good, good to prevent the magnetic roller by force from the in-situ. Then you can install toner, and to shake and slowly poured into the toner for the bunker, the Shang Hao parts magnetic roller and fixed to the final end should be gently rotating magnetic roller gear for a few laps for the benefit of carbon uniform powder attached.

Let's look at the collection part, in this part we have to do is to replace the new drum. Using the same method to allocate the fixed pin, remove the photosensitive drum, and then to collect part of the Feifen Feifen clean (clean as possible, so as not to influence the new drum print quality), this, we can install a new drum a. Installation should pay attention to, photosensitive drums usually around the points, the butt end with gear installed, you use just set aside a fixed pin Shanghao under the drum.

The new photosensitive drums are generally a shade of ink, anti-exposure of seals do not tear off prior to installation to prevent the exposure, the installation only after a good check and correct torn off. In this way, for the pink part and the collection of parts were somehow, the last as long as the two parts according to the circumstances apart to install recovery, plugged in a fixed bayonet, the entire replacement will be declared completed.

During the replacement process, if there are printer toner falls out, it is best to use vacuum cleaner sucked, and then scrub it again pure alcohol. Moreover, the entire replacement process is best carried out in the dark of the studio to prevent the exposure of photosensitive drum. For integrated toner replacement, can be described as very simple, as long as the complete replacement of the entire cartridge can be won, and saved a lot of trouble, but remember the best to pre-loaded toner shake. In addition I would also like to remind you that, when breaking the seal cartridge is usually valid for two and a half, but once the shrink-wrap the validity period of only 6 months, and the user should pay attention to the use within the validity period to ensure print quality.

Note:

In the maintenance and replacement of toner cartridges in the same time, some areas need to re-draw attention to this:

1. Cleaning cartridges do not have too frequently, in the cleaning process prohibit the use of plain paper scrub.

2. In the above-mentioned maintenance and replacement of the process, forbidden by hand touched the surface of photosensitive drum, and guard against a hard object collisions.

3. Try not to let cartridge exposed to direct sunlight or strong light, the Do not open the cartridge on the block light board, if exposed to bright light in a row for more than ten minutes, the worst case, photosensitive drum that is declared obsolete.

4. Avoid high humidity, high temperature, high-altitude environment, the use and preservation of toner cartridges, once inside the agglomeration moisture will affect the printing or cause print less coloration, while in the cartridge to get from the low temperature environment work, it is best to set aside a period of time (one hour or more) re-use.

5. Do not arbitrarily hand turn OPC OPC, OPC OPC must pay attention to the direction of rotation, if the rotation in the wrong direction will cause damage to parts when you print or print stains leaking powder.

6. Cartridge with an imaging device, it is a roller covered with magnetic particles, it is necessary to ensure that the cartridge away from the monitor, hard disk, speakers and other magnetic material, to avoid the phenomenon of magnetization, thus affecting the print quality.